Fencing & decking
Materials for a 20 m timber paling fence
To build a 20 m timber paling fence that is 1.8 m high, you will need 10 posts, 27 rails (at 2.4 m lengths), 200 palings (100 mm wide), and 20 bags of 20 kg Post Mix concrete.
Shopping list
| Item | Buy | Note |
|---|---|---|
| Posts | 10 posts | at most 2.4 m apart; about 600 mm in the ground |
| Rails, 2.4 m lengths | 27 rails | 3 per bay at 1800 mm high |
| Palings, 100 mm wide | 200 palings | edge to edge |
| Post Mix concrete, 20 kg bags (post holes) | 20 bags | 2 bags a hole, for a hole 2 × the post width |
- The 2-bag figure is Bunnings Post Mix advice for a hole 2 × the post width. A wider or deeper hole needs more bags.
How this was worked out
- Panels (bays):
length ÷ post spacing, rounded up
20000 ÷ 2400 = 9 bays - Posts:
bays + 1
9 + 1 = 10 posts - Rails:
bays × rails per bay
9 × 3 = 27 rails - Palings:
length ÷ (paling width + gap), rounded up
20000 ÷ (100 + 0) = 200 palings - Concrete for posts:
posts × bags per hole
10 × 2 = 20 bags
Timber Paling Fence Requirements
When planning a timber paling fence, the primary components consist of posts, rails, and the palings themselves. For a standard 1.8 m high fence, the structural integrity depends on the spacing of the posts and the number of horizontal rails used to support the vertical palings.
Timber Queensland TDS 20 Residential Timber Fences specifies that for fences between 1200 mm and 1800 mm high, posts should be set about 600 mm deep. For shorter fences up to 1200 mm high, a depth of 450 mm is sufficient. The maximum post spacing for rails measuring 100 x 38 mm is 2400 mm. If you choose to use 75 x 38 mm rails, the maximum spacing reduces to 2100 mm.
The number of rails required changes based on the height of the fence. Timber Queensland TDS 20 Residential Timber Fences states that two rails are sufficient for paling fences up to 1200 mm high. However, for fences over 1200 mm and up to 1800 mm high, three rails are required. Common paling sizes for these projects include 100 x 15 mm and 75 x 15 mm.
Concrete and Post Installation
Securing the posts in the ground requires adequate concrete. The Bunnings Easy Mix Post Mix technical data sheet provides specific guidelines for this. It states that the hole width should be twice the width or diameter of the post. For the installation of each post, the technical data sheet recommends using approximately two 20 kg bags of Post Mix per hole.
When calculating your total concrete needs, you must multiply the number of posts by the bags required per hole. For a 20 m fence requiring 10 posts, this results in 20 bags of 20 kg Post Mix. If you are using a different type of concrete, such as a standard concrete mix, you should refer to the slab calculator on this site to determine the volume required, as the Boral and Cement Australia concrete mix figures differ from the Post Mix figures.
Steel Sheet Fence Alternative
An alternative to timber palings is the use of steel fence sheets. This method often involves using 3-sheet panels. According to the Lysaght fence and gate installation guide (non-cyclonic), a 3-sheet panel has a width of 2350 mm, which corresponds to the post spacing. Other configurations include 2-sheet panels with a width of 1582 mm and 4-sheet panels with a width of 3100 mm.
For a 20 m fence using the 3-sheet panel style, the requirements shift to 9 panels and 27 steel fence sheets. The number of posts remains the same at 10, and the concrete requirement remains 20 bags of 20 kg Post Mix. Choosing between timber and steel depends on your desired aesthetic and the specific panel widths available from your supplier.
Post depth and how the concrete is counted
Two sourced figures decide the concrete. Timber Queensland's residential fence guide has timber posts set about 600 mm into the ground, and Bunnings' Post Mix data sheet says to dig the hole to one third of the post's length and twice the post's width, using about two 20 kg bags per hole. The calculator multiplies the posts by those two bags, which is why a 20 m fence with 10 posts shows 20 bags. A wider or deeper hole takes more concrete, so treat the bag count as the minimum for a hole of that size and check the data sheet for your own post. Fence posts also differ from slabs: Post Mix is a different product from slab concrete mix, with its own yield per bag, so do not use these bag counts to estimate a slab.
Material Summary Table
The following table outlines the materials required for a 20 m fence at a height of 1.8 m for both timber and steel options.
| Material Type | Timber Paling Fence | Steel Sheet Fence (3-sheet) |
|---|---|---|
| Posts | 10 posts | 10 posts |
| Rails (2.4 m lengths) | 27 rails | N/A |
| Palings (100 mm wide) | 200 palings | N/A |
| Steel Sheets | N/A | 27 sheets |
| Steel Panels | N/A | 9 panels |
| Post Mix Concrete (20 kg bags) | 20 bags | 20 bags |
Worked Example
To understand how the calculator arrives at these figures, we can look at the 20 m timber paling fence scenario.
First, we determine the number of bays. For a 20 m fence with a maximum post spacing of 2.4 m, the calculation results in 9 bays.
Next, we calculate the posts. With 9 bays, you need 10 posts (one for each end and one for each internal bay).
Then, we calculate the rails. For a fence height of 1.8 m, three rails are required per bay. With 9 bays, this equals 27 rails.
For the palings, the 20 m length is divided by the 100 mm width. This results in 200 palings.
Finally, for the concrete, the 10 posts each require 2 bags of 20 kg Post Mix, totaling 20 bags.
Common Mistakes
One frequent error is underestimating the number of rails needed for taller fences. While two rails may suffice for a 1.2 m fence, a 1.8 m fence requires three rails to maintain structural integrity. Another common mistake is incorrect post hole sizing. The Bunnings Easy Mix Post Mix technical data sheet clarifies that the hole width must be double the post width; digging a hole that is too narrow will result in insufficient concrete coverage.
Frequently Asked Questions
How deep should I bury my fence posts?
For fences between 1200 mm and 1800 mm high, Timber Queensland TDS 20 Residential Timber Fences recommends a post depth of about 600 mm. For fences up to 1200 mm high, a depth of 450 mm is sufficient.
How many rails do I need for a 1.8 m fence?
According to Timber Queensland TDS 20 Residential Timber Fences, fences over 1200 mm and up to 1800 mm high require three rails.
What is the maximum spacing for timber posts?
Timber Queensland TDS 20 Residential Timber Fences states that rails measuring 100 x 38 mm allow for a maximum post spacing of 2400 mm. If using 75 x 38 mm rails, the maximum spacing is 2100 mm.
How much concrete do I need per post hole?
The Bunnings Easy Mix Post Mix technical data sheet suggests using approximately two 20 kg bags per post hole.
What is the width of a 3-sheet steel fence panel?
The Lysaght fence and gate installation guide (non-cyclonic) specifies that a 3-sheet panel has a width of 2350 mm.
Sources and assumptions
These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them to match your product and your site.
Keep reading
- How much concrete do I need for a 3 x 3 m slab?A 3 x 3 m slab at 100 mm needs 104 bags of 20 kg mix, or 1 m³ ready-mix. See the base, other sizes and what…
- How many 20 kg bags of concrete make a cubic metre?Brands list 100 to 110 bags of 20 kg mix per cubic metre. Here is why they differ, how to read your bag, and…