EnoughToGet CalculatorsGuides

Paint & plaster

How many litres of paint for a bedroom?

By the EnoughToGet teamUpdated 2026-11-186 min readSources and assumptions

To determine how many litres of paint you need for a bedroom, you must calculate the total surface area of the walls and ceiling, subtract the area of doors and windows, and then divide by the specific coverage rate of your chosen paint brand.

Try itPaint: enter your own sizes
m
Type metres, for example 4.2.
m
m
Each door is taken off the wall area.
Each window is taken off the wall area.
The ceiling uses the same paint here. Ceiling paint is often a different product.
Two coats is the usual advice on the label.
%
Covers rough surfaces and touch-ups.
You need
4.51 L
buy 5 L in cans

Shopping list

ItemBuyNote
Paint needed4.51 L2 coats over 32.8 m²
4 L can1 can5 L bought in total
1 L can1 can5 L bought in total
  • Coverage is 16 m² per litre (Dulux calculator). Check the spread rate on your can: textured walls and dark colours use more.
How this was worked out
  1. Wall area: perimeter × height
    2 × (4 + 3.5) × 2.4 = 36 m²
  2. Minus openings: walls − doors × door area − windows × window area
    36.00 − 1 × 1.7 − 1 × 1.5 = 32.8 m²
  3. Paint needed: area × coats × (1 + waste) ÷ coverage
    32.80 × 2 × 1.10 ÷ 16 = 4.51 L

Understanding Paint Coverage Rates

Before you start buying cans, it is essential to understand that paint coverage is not universal. The amount of surface area a single litre of paint can cover depends heavily on the brand and the specific product formulation. In Australia, the Dulux paint calculator page estimates that for most topcoats, you should assume a coverage of 16 m2 per litre, based on a two-coat application.

If you are working on a project in New Zealand, the requirements differ significantly. The Resene paint calculator page uses Resene SpaceCote Low Sheen as an example, which has a theoretical spreading rate of 11 m2 per litre. Because the New Zealand coverage rate is lower, you will generally require more litres of paint to cover the same physical area compared to an Australian project. Always check the specific product data sheet or the can label to confirm the spread rate for the exact product you intend to purchase.

Calculating Your Surface Area

To get an accurate estimate, you need to measure the dimensions of your room. Start by measuring the length and width of the floor to determine the ceiling area. Then, measure the height of the walls. By multiplying the perimeter of the room by the height, you can find the gross wall area.

From this gross total, you must subtract the areas that will not be painted. Standard internal doors are typically calculated as 1.7 m2, while a typical window opening is estimated at 1.5 m2. Subtracting these openings ensures you do not over-purchase materials. For a standard bedroom, these subtractions are vital for maintaining an accurate paint volume calculation.

Accounting for Coats and Waste

Most professional results require at least two coats of topcoat. The Dulux paint calculator page assumes 2 coats as the ideal number for most paints to ensure a consistent finish and proper opacity. When calculating your total volume, you must double the area of your walls and ceiling before dividing by the coverage rate.

Furthermore, it is a common trade rule of thumb to include a waste factor. A 10% waste margin is standard for accounting for spillage, roller absorption, and future touch-ups. This ensures that you do not run out of paint halfway through the final coat, which can lead to visible lap marks or uneven finishes.

Comparison of Regional Requirements

The following table illustrates how different room sizes and regional coverage rates affect the total amount of paint required. These figures assume two coats of paint and a 10% waste factor.

ScenarioRegionWall AreaOpeningsCeilingTotal AreaPaint NeededRecommended Cans
Standard RoomAU36 m²32.8 m²No32.8 m²4.51 L1 x 4 L, 1 x 1 L
Standard RoomNZ36 m²32.8 m²No32.8 m²6.56 L1 x 4 L, 1 x 2 L, 1 x 1 L
Standard RoomAU36 m²32.8 m²Yes46.8 m²6.44 L1 x 4 L, 1 x 2 L, 1 x 1 L
Standard RoomNZ36 m²32.8 m²Yes46.8 m²9.36 L1 x 10 L
Large RoomAU48.6 m²42.2 m²Yes62.2 m²8.55 L2 x 4 L, 1 x 1 L
Large RoomNZ48.6 m²42.2 m²Yes62.2 m²12.44 L1 x 10 L, 1 x 2 L, 1 x 1 L

Worked Example: Standard Australian Bedroom

To understand how these figures are reached, let's look at the first scenario in the table: a standard Australian bedroom with walls only (no ceiling).

First, we calculate the wall area. For a room with a length of 4 metres, a width of 3.5 metres, and a height of 2.4 metres, the perimeter is 15 metres. Multiplying the perimeter by the height gives a gross wall area of 36 m².

Next, we subtract the openings. The calculation assumes one door (1.7 m2) and one window (1.5 m2), totaling 3.2 m2 of openings. Subtracting this from the gross wall area leaves a net paintable area of 32.8 m².

Because we are applying two coats, the total area to be covered is 65.6 m². Using the Australian coverage rate of 16 m2 per litre, we divide 65.6 by 16, which equals 4.1 L. Finally, we add the 10% waste factor. Adding 10% to 4.1 L brings the total to 4.51 L. To complete this job, you would need to purchase a combination of cans, such as one 4 L can and one 1 L can.

Choosing the Right Can Sizes

Knowing the total litres required is only half the battle; you also need to know how to purchase them. Paint is typically sold in various sizes to suit different project scales. Common sizes include 1 L, 2 L, 4 L, 10 L, and 15 L cans.

Common Mistakes

One of the most frequent mistakes homeowners make is failing to account for the number of coats. A single coat of paint is rarely sufficient to achieve a professional finish, especially if you are changing colours. Always calculate for at least two coats.

Another common error is neglecting the waste factor. If you buy the exact amount of paint required for the surface area without accounting for the 10% waste, you will likely run out of paint before the job is finished. This can result in "holidays" or visible lines where the paint thickness changes.

Finally, many people forget to subtract the area of windows and doors. While this might seem like a small difference, in a room with multiple large windows or double doors, it can significantly impact the amount of paint you need to buy. Always measure your openings accurately to ensure your order is correct.

Frequently Asked Questions

How do I handle different wall textures?

Rougher surfaces like brick or textured render will absorb more paint than smooth plasterboard. If your walls are not smooth, you should check your product label or supplier for a reduced coverage rate.

Should I buy more paint than the calculator suggests?

The calculator includes a 10% waste factor, which is a standard trade rule of thumb. If you are painting a very large area or a very porous surface, you may want to consider a slightly higher margin, but for most standard bedrooms, the 10% is sufficient.

Does the ceiling require the same paint as the walls?

Not necessarily. While you can use the same paint, many homeowners prefer a different finish or colour for the ceiling. If you choose a different paint, you must calculate the ceiling area separately using the coverage rate for that specific product.

What happens if I run out of paint before finishing the second coat?

If you run out, try to find the exact same batch of paint. Different batches can have slight variations in colour. If you cannot find the same batch, it is best to finish the first coat completely and then decide if you need to purchase more for the second.

How do I calculate the area of my windows?

Measure the height and width of the window in metres. Multiply these two numbers together to get the area in square metres. For example, a window that is 1.5 metres tall and 1 metre wide has an area of 1.5 m2.

Sources and assumptions

These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them to match your product and your site.

SettingValueStatusSource
paint coverage per litre16 m2/L
New Zealand: 11 m2/L
Verified 2026-11-18Dulux paint calculator page: estimates assume two-coat topcoat coverage at a spread rate of 16 m2 per litre (check the can).
paint coats2 coatsVerified 2026-11-18Dulux paint calculator page: assumes 2 coats of topcoat, the ideal number for most Dulux paints.
paint waste10 %Editable defaultcommon trade rule of thumb for touch-ups and spillage, editable
paint door area1.7 m2Editable defaultapprox. standard 2040 x 820 mm internal door, editable
paint window area1.5 m2Editable defaulttypical window opening, editable
paint can size 1l1 LVerified 2026-11-18Dulux Wash&Wear Low Sheen product page lists pack sizes 500 mL, 1, 2, 4, 10 and 15 L.
paint can size 2l2 LVerified 2026-11-18Dulux Wash&Wear Low Sheen product page lists pack sizes 500 mL, 1, 2, 4, 10 and 15 L.
paint can size 4l4 LVerified 2026-11-18Dulux Wash&Wear Low Sheen product page lists pack sizes 500 mL, 1, 2, 4, 10 and 15 L.
paint can size 10l10 LVerified 2026-11-18Dulux Wash&Wear Low Sheen product page lists pack sizes 500 mL, 1, 2, 4, 10 and 15 L.
paint can size 15l15 LVerified 2026-11-18Dulux Wash&Wear Low Sheen product page lists pack sizes 500 mL, 1, 2, 4, 10 and 15 L.

Keep reading